Cleanses / Device User Guide
Laxmi Zapper Guide Manual
Read this only if you have done a liver cleanse. Otherwise, this article on parasite cleanse is NOT FOR YOU.

Table of Contents
Before You Start
Read this only if you have done a liver cleanse
Otherwise, this article on parasite cleanse is NOT FOR YOU.
Please read the Parasite Cleansing chapter of the book “Cleansing Therapy” — read it here, or download it from –
Also watch the “Parasite Cleanse” YouTube video by Dr Piyush Saxena, and for usage by Arjun and Ramesh Pandya Ji.
Clarkia Tincture — 3 times a day
- Take 10 drops of Clarkia Tincture (USA-made only) three times a day, 10 drops in half a cup of water.
- Follow suppliers’ instructions for usage if they differ from our recommended dosage.
- Don’t consume made-in-India parasite tinctures sold in online shops like Amazon, Flipkart, etc.
herbasale.eu — Colon Active Tincture by Dr. Hulda Clark or sites which sell Clarkia products directly.
If not available, then take any one of the Homeopathy:
- Dr. Reckeweg R56 Worms Drop
- Wheezal WL42
- REPL Dr. Advice No 105 (Worms)
- Cina Dilution 200 CH
Take 10 drops three times a day in half a cup of water for one week.
Note
We have used “Zapper Machine” to mean the “Laxmi Zapper Pulser” device. The Laxmi Zapper Pulser is intended for use by a single individual at a time.
Consuming Colloidal Silver Water — 3 times a day
- Attach the Silver Rods with a connector and connect this to the Zapper Machine.
- Put the Silver rods in a glass full of water (do not use a metal pot/bottle) in a glass/plastic pot/bottle.
- Press the Mode button of the Zapper Machine 7 times to get Silver Mode.
- Press the Start button once to get it on for 10 minutes. The colloidal silver water maker has started working now.
- After 10 minutes, the colour of the water will turn milky (for more concentrated and darker Colloidal Silver, rerun it for 10 min). Medicine is ready.
- Switch OFF the Zapper Machine. Detach silver rods from the Zapper Machine. Clean them and pack it.
Note
Do NOT use the RO water, use only Tap or Mineral water.
Drink 50 ml of Colloidal Silver water three times a day. For more dosage information, read the article on dosage in the book “Cleansing Therapy.” Colloidal Silver is sensitive to light. Please keep it in a coloured glass bottle and store it in a dark place, e.g., your refrigerator.
Using Pulser — 3 times a day
Before Starting
- Make sure that the Zapper Machine Power is OFF.
- Connect the Copper Pipes with the Zapper Machine.
- Rotate the rotary/regulator to the extreme left.
- Take two small towels. Soak them in plain salty water.
Instructions for 4 Hz
- Switch on the Zapper Machine, press the “Mode” button once to get Pulser 4 Hz. Press the “Start” to start zapping.
- Wrap the wet towels around the Copper Pipes and hold the Pipes in both hands.
- Press the Start button in the Zapper Machine. Zapping starts.
- Slowly rotate the rotary/regulator to the right side. It will start increasing the voltage. Keep rotating to increase the current as much as you can bear.
- When the Pulser stops after 10 minutes, switch OFF the Zapper Machine, rotate the rotary/regulator to the extreme left.
- Relax for a few minutes.
Note: Various variants of using the Pulser / Zapper are
- Copper Rods wrapped with/without wet towels with/without salt in both hands.
- One Copper Rod is wrapped with a wet towel in the right hand, and another is on the sole of the left foot. After some time, alternate hands and feet. If necessary, tighten the rods with rope or straps.
- One Copper Rod is wrapped with a wet towel on the left foot's sole, and another Copper rod is on the right foot's sole, thus covering both legs and the pelvic portion.
- Place the Copper Pipes (covered with a wet towel) below the soles of both feet and tighten them with rope or straps.
- Look for locations to keep the pipes, e.g., armpits and behind the knees.
- One wet towel was wrapped around the pipe below the waist, and the other wet towel was wrapped by hand above the abdomen at various locations. Keep on moving it.
You may take a glass of dilute buttermilk. It helps.
Instructions for 16 Hz
Switch on the Zapper Machine and press the Mode button 2 times to get Pulser 16 Hz. Press the “Start” to start zapping. The other instructions remain the same.
Instructions for 100 Hz
Switch on the Zapper Machine and press the Mode button three times to get Pulser 100 Hz. Press the “Start” to start zapping. The other instructions remain the same.
Using Zapper — 3 times a day
Before Starting
- Make sure Zapper Machine Power is OFF.
Instructions for 2128 Hz
Switch ON the Zapper Machine and press the “Mode” button four times to get 2128 Hz. Press “Start” to start zapping. It will run for 6-7 minutes. The other instructions remain the same.
Instructions for 10 KHz
Switch ON the Zapper Machine and press the “Mode” button 5 times to get 10 KHz. Press the “Start” button to start zapping. It will run for 6-7 minutes. Other instructions remain the same.
Instructions for 30 KHz
Switch ON the Zapper Machine and press the “Mode” button 6 times to get 30 KHz. Press the “Start” button to start zapping. It will run for 6-7 minutes. The other instructions remain the same.
Note
This is one cycle; repeat it thrice daily for at least 3 days.

These frequencies of 4 Hz, 16 Hz and 100 Hz Pulser are square wave 9 v and 2128 Hz, 10 KHz and 30 KHz Zapper are sinusoidal waves. All these 6 frequencies kill different range of parasites. In 3 days, many of them are killed in egg, larva, pupa and adult parasite i.e., all 4 stages of parasites’ life.
The user guide in Hindi is separately available.
The Laxmi Zapper Shipped With the Following Items
- One Laxmi Zapper Pulser device
- One Pair of Silver Rods and a socket/port. It is suitable for 3000 glasses of water.
- One Pair of Copper Pipes with wire and socket/port
- One Power Cable along with 9V/1A DC Adapter
Buy yourself a scrubber, Scotch-Brite, Scrub Pad, and Pitambari to clean copper pipes and silver rods.
A Few Ways to Use the Zapper Machine






Using Other Purchased Optional Accessories
Using Footplates and Copper Rods

Using Electrode Pads

For wiring, mode selection, and how to connect the footplates and electrode pads, see the Laxmi Zapper Pulser Device Guide.
Related guides
- Laxmi Zapper Pulser Device Guide — wiring, ports, mode selection, and accessory connections.
- Laxmi Zapper vs Zenthera Zapper — a side-by-side comparison of both devices.

